AZA 0793 FLOW TABLE

IS 4031, 2645, 2542 (PART-1), 1727, 5513 & 712. BS 12, 146, 915, 1370, 4027, 4246, 4248, AASHTO T 129, E 131.
This instrument is used for determining the normal consistency and setting times of cement and 'A' class limes. Specification: The apparatus consists of a metallic frame bearing a freely movable and with a cap at top, one vicat mould and glass base plate and one set of needles one each initial needle, final needle and consistency plunger. It comes with a dashpot which facilities gentle lowering of the needles. Accessories: Mild steel base plate 5 inches x 5 inches. Fulcrum MOULD, brass,80mm i.d. base dia x 70mmi.d.top dia, 40mm height. Note Normally set of needles and mould which meet is Requirements as per I.S. 5513 are supplied. While ordering please specify the specification code of the instrument required. Vicat needle apparatus for determining consistency of hydraulic cement. Gypsum plaster, lime etc.
As per ASTM C 187-58 C 472-62 C 110-58, IS 2542 (Part-1) can also be supplied.

IS1727 1967,IS4031 1968,ASTMC394,C64 For making standard rectangular specimens of 40 x 40 x 160mm. of Portland and pozzolana cement mortar for determining the transverse strength. Specification: The jolting apparatus consists of a rectangular table rigidly connected by two support arms to a spindle at a horizontal distance of 800 mm from the centre of the table. There is a projecting lug with a plane face on the upper face of the table beneath which is a stop with a rounded upper surface. The table can be raised and allowed to fall freely on the stop by a cam which is connected to a motor and gearbox through a V-belt an pulleys. The cam rotates at a rate of 60 Rev/Min. A stroke counter fitted with micro-switch is provided which stops the machine after 60 Jolts. Locating pins are provided for mounting the mould compartments on the table. The mould surmounted by the hopper can be clamped rigidly to the table. Supplied complete with mould and hopper. Suitable for operation on 230 Volts, Single Phase, A.C. Supply. A Digital Preset Counter can be supplied at an extra cost.

Spares and Accessories: (1) Steel mould with base plate having three compartments each having 40x40x160mm, internal dimensions. (2) Apparatus for de-moulding the specimen.

(2) Apparatus for de-moulding the specimen.

IS4031 1968, IS1344 1959, BS 4550. Concrete moulds are easily cast by using a tamping bar or a vibrating table. However air trapped in cement mortar paste cannot be thus removed while casting cement mortar moulds. Easy method is to impart greater vibrating of lesser amplitude to the mould while casting This is achieved in a vibrating machine. Vibrating machine is used for the preparing of mortar cubes for the determination of compression strength of ordinary and rapid hardened Portland cement, low heat Portland cement, Portland blast furnace cement and high alumina cements.

Specification:

The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base. The complete frame assembly consists of a vice to hold a 70.6 mm cube mould and two studs threaded at top and a hopper to feed the sample in the mould. This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame. A balance weight is an integral bottom part of the frame. The center of gravity of the assembly is brought to the centre of the eccentric shaft within a distance of 25 mm below it. The electric motor drives the shaft of the frame and thus imparts required vibration to the moulds.

The frequency of vibration is 12000 +/- 400 Vibration Per Minute. Supplied complete with on 70.6 mm Cube Mould with loose base plate, a time switch 0-5mins x 1mm.

Spares: Set of springs, belt and belt guard. Optional: Digital Preset Timer can be supplied at an extra cost.