Rock
Aggregate
Cement
Concrete
Soil
Steel
Bitumen/Asphalt
Security Survey Equipment
General Items
AZA 0874 RAPID MOISTURE METER
The unit consists of a pressure vessel with clamp for
sealing cap, capacity is 6 gms. Rubber sealing gasket,
pressure gauge calibrated in percentage moisture
content on the wet weight basis, a counter poised
balance for weighing sample, a scoop for measuring
carbide reagent, a bottle of reagent, one cleaning brush
and a set of 4 steel balls for thorough mixing . Complete
in highly polished wooden carrying case with handle.
AZA 0874A : Pressure gauge calibrated
0-50% x 0.50%
AZA 0874B : Pressure gauge calibrated
0-25% x 0.25%
Spares:
Carbide reagent, in bottles of 500 gms. each available
on extra cost
Category: Soil
Related products
AZA 0848 PLASTIC LIMIT SET
IS 2720 (PART-VII) ASTM D-42, BS 1377 AASHTO T 90 Moisture contents at which soil has smallest plasticity is called limit. For determination purpose plastic limit is defined as the water content at which a soil will just begin to crumble when rolled in to a thread of 3mm dia.
Specification:
The complete set consists of one each:
1. Glass plate 20cm x 15cm having round ends
2. Brass or stainless steel rod 3mm dia x 150mm long
3. Flexible spatula 15 cm
4. Set of 6 moisture containers
5. Porcelain basin 150mm dia
6. Plastic wash bottle 500ml
Note: Glass Plate size 500 x 500 x 10mm can be supplied at an extra cost
AZA 0849 SHRINKAGE LIMIT SET
IS 2720 (PART-VII) ASTM D 427, BS 1377, AASHTO T 92. Shrinkage limit is the maximum water content at which a reduction in water content does not cause an appreciable reduction in volume of the Soil Mass. At shrinkage limit, on further reduction in water, air enters in to the voids of soils and thus keeps the volume constant.
The apparatus can be used to determine shrinkage limit and to calculate other shrinkage ratio, shrinkage index and volumetric shrinkage.
Set consists of one each:
1. Porcelain evaporating dish
2. Shrinkage dish
3. Glass cup
4. Perspex plate with three metal prongs
5. Flexible spatula 100mm
6. Glass cylinder
7. 25ml x 1ml, supplied without mercury
6. Plastic wash bottle 500ml
Optional Accessories:
Mercury supplied in bottle of 500 gms. at an extra cost.
AZA 0852 SEMI AUTOMATIC CONE PENETROMETER
BS 1377:2
Specification:
Used to determine the moisture content at which clay soils pass from a
plastic to a liquid state. Two Version are available. One the standard one
& the other is semi-automatic with timer where the cone is allowed to free
fall for a period of 5 seconds including one each of 50 gm. & 100 gm.
weight, one penetration cone, preset counter & measuring cup.
AZA 0859 SAND EQUIVALENT TEST SET
ASTM D 2419, AASHTO T 176
Specification:
Used to determine the relevant proportions of clay-like or Plastic
fines and dust in granular soils & fine aggregate
Consists of:
1. Acrylic graduated cylinder (4 nos.)
2. Rubber stopper for cylinder (4 nos.)
3. Graduated Steel rule 450 mm
4. Funnel 100 mm plastic
5. Aspirator bottle 5 lts plastic with rubber cock
6. Stand for the aspirator bottle with siphon assembly
7. Irrgation tube with stop pinch cock & weighted foot assembly
Optional : Stock solution can be supplied at an extra cost
AZA 0865 HEAVY COMPACTION TEST
AZA 0868 PROCTOR NEEDLES (SPRING TYPE)
Specification:
The instrument consists of a needle attached to
a spring loaded plunger, the stem of which is
calibrated to read 0 to 40 kg division. Long
stem is graduated at every 12.5mm to read
depth of penetration and for use with needles of
larger areas . The small penetration stem is also
graduation in 12.5mm division and is used
with needles of smaller areas. Needle points
one each of 0.25, 0.5, 1.0, 1.5, 2.0, 3.5 and
6.0 sq cm. And one Tommy pin is supplied.
Complete as above in a wooden carrying
case.
AZA 0869 POCKET PENTROMETER
ASTM D 1558 D 2573
This instrument is used to estimate approximate unconfined
compressive strength and the estimation to shear strength of soil
Cohesive soils can also be classified in terms of consistency
using this Penetrometer. This is a handy and convenient
instrument.
Specification:
It consists of a light weight barrel assembly with a polished and
ground steel loading piston plunger. A direct reading scale is
engraved on the piston barrel and indicates load in kg. / sq.
cm. A maximum load indicator ring is provided on the
penetration plunger. The calibrated spring is heat treated and
plated for rust resistance. The barrel diameter is 20mm and the
length 150mm. Supplied with carrying case
AZA 0872 DYNAMIC CONE PENETROMETER
A simple and robust instrument for rapid in-situ measurement of the structural properties of road pavements
! Provides fast and efficient method of obtaining information
! For continuous measurements up to a depth of 800 mm and 1,200 mm with the extension rod.
! Portable and can be accommodated in a carrying case
for pavement design. Agreement is generally good over most of the range but differences are apparent at low values of
CBR, especially for fine grained materials.
It incorporates a 8 Kg weight dropping through a height of 575 mm and a 60 deg. cone having a diameter of 20 mm.
It is supplied complete with assembly tools and weighs 20 Kg approx.
The DCP needs three operators, one to hold the instrument, other to raise and drop the weight and a technician to
record the results. The instrument is held vertically and the weight carefully raised to the handle limit and then allowed
to fall onto the anvil.
The equipment consist of the following replaceable parts
AZA 0872A Top and Bottom Rod
AZA 0872B Handle
AZA 0872C Hammer
AZA 0872D 1m Scale
AZA 0872E 60 deg. Cone
AZA 0872F Anvil
